Sorter V2 - 24V power distribution

Diagram

PSU box pigtails PJ1-PJ3 and load cables W1-W3. The PSU end
and the board end follow Jon's DC_PSU_Harness and
DC_basicallyV1_3_Harness drawings (2026-08-08), which are
the source of truth for those. Values marked GUESS are
guesses, not measurements.
%3 PSU PSU LRS-350-24 terminal block 9-pin AC/L 1 AC/N 2 FG 3 -V 4 -V 5 -V 6 +V 7 +V 8 +V 9 Screw numbers are MeanWell's (LRS-350-SPEC) One pigtail per pair: 7+4, 8+5, 9+6 Screws 1-3 are mains, on the IEC inlet's own leads Terminal spec: see the PSU output pigtail drawing PJ1 PJ1 2x 18 AWG 4.0 in   PSU:7:+V     1:RD     J1:1:+24V (tip) PSU:4:-V     2:BK     J1:2:GND (sleeve)   PSU-J pigtail, inside the PSU box Comes attached to the jack already, so buy the jacks with leads rather than have these made PSU:e--PJ1:w PSU:e--PJ1:w PJ2 PJ2 2x 18 AWG 4.0 in   PSU:8:+V     1:RD     J2:1:+24V (tip) PSU:5:-V     2:BK     J2:2:GND (sleeve)   PSU-J pigtail, inside the PSU box Comes attached to the jack already, so buy the jacks with leads rather than have these made PSU:e--PJ2:w PSU:e--PJ2:w PJ3 PJ3 2x 18 AWG 4.0 in   PSU:9:+V     1:RD     J3:1:+24V (tip) PSU:6:-V     2:BK     J3:2:GND (sleeve)   PSU-J pigtail, inside the PSU box Comes attached to the jack already, so buy the jacks with leads rather than have these made PSU:e--PJ3:w PSU:e--PJ3:w J1 J1 DC jack 5.5x2.1 female, panel-mount 2-pin 1 +24V (tip) 2 GND (sleeve) P1 P1 DC plug 5.5x2.1 male 2-pin +24V (tip) 1 GND (sleeve) 2 J1:e--P1:w J2 J2 DC jack 5.5x2.1 female, panel-mount 2-pin 1 +24V (tip) 2 GND (sleeve) P2 P2 DC plug 5.5x2.1 male 2-pin +24V (tip) 1 GND (sleeve) 2 J2:e--P2:w J3 J3 DC jack 5.5x2.1 female, panel-mount 2-pin 1 +24V (tip) 2 GND (sleeve) P3 P3 DC plug 5.5x2.1 male 2-pin +24V (tip) 1 GND (sleeve) 2 J3:e--P3:w W1 W1 2x 18 AWG 36.0 in   P1:1:+24V (tip)     1:RD     BOARD_PWR:1:+24V P1:2:GND (sleeve)     2:BK     BOARD_PWR:2:GND   board 24V in Length deliberately long P1:e--W1:w P1:e--W1:w BOARD_PWR BOARD_PWR JST VH 2-pin (VHR-2) female 2-pin 1 +24V 2 GND Additional components 2 x #8 (Terminal - SVH-21T-P1.1) basically board v1.3 24V input Pin 1 = +24V, pin 2 = GND W2 W2 2x 22 AWG 12.0 in   P2:1:+24V (tip)     1:RD     HUB:1:+24V (tip) P2:2:GND (sleeve)     2:BK     HUB:2:GND (sleeve)   USB hub, double-male. Gauge = GUESS, not covered by Jon's drawings. P2:e--W2:w P2:e--W2:w HUB HUB DC plug 5.5x2.1 male 2-pin 1 +24V (tip) 2 GND (sleeve) into the Waveshare hub jack (DC-044, 5.5x2.1) W3 W3 2x 22 AWG 6.0 in   P3:1:+24V (tip)     1:RD     BUCK:1:+24V P3:2:GND (sleeve)     2:BK     BUCK:2:GND   Orange Pi buck. Gauge = GUESS, not covered by Jon's drawings. P3:e--W3:w P3:e--W3:w BUCK BUCK Bare tinned leads 2-pin 1 +24V 2 GND splice to the 24V-5V USB-C buck input leads PJ1:e--J1:w PJ1:e--J1:w PJ2:e--J2:w PJ2:e--J2:w PJ3:e--J3:w PJ3:e--J3:w W1:e--BOARD_PWR:w W1:e--BOARD_PWR:w W2:e--HUB:w W2:e--HUB:w W3:e--BUCK:w W3:e--BUCK:w

Bill of Materials

Id Description Qty Unit Designators Manufacturer MPN
1 Cable, 2 x 18 AWG 48 in PJ1, PJ2, PJ3, W1
2 Cable, 2 x 22 AWG 18 in W2, W3
3 Connector, Bare tinned leads, 2 pins 1 BUCK
4 Connector, DC jack 5.5x2.1 female, panel-mount, 2 pins 3 J1, J2, J3
5 Connector, DC plug 5.5x2.1 male, 2 pins 4 HUB, P1, P2, P3
6 Connector, JST VH 2-pin (VHR-2), female, 2 pins 1 BOARD_PWR
7 Connector, LRS-350-24 terminal block, 9 pins 1 PSU
8 Terminal - SVH-21T-P1.1 2 BOARD_PWR JST SVH-21T-P1.1